spec no: dsaj8791 rev no: v.5b date: jan/20/2015 page: 1 of 6 approved: wynec checked: allen liu drawn: q.m.chen erp: 1101026815 5mm round led lamp attention observe precautions for handling electrostatic discharge sensitive devices part number: wp9294zgc/g green features ? high luminous emission. ? low power consumption. ? general purpose leads. ? reliable and rugged. ? long life - solid state reliability. ? rohs compliant. descriptions ? the green source color devices are made with ingan light emitting diode. ? electrostatic discharge and power surge coul d damage the leds. ? it is recommended to use a wrist band or anti- electrostatic gl ove when handling the leds. ? all devices, equipments and machineries must be electrically grounded. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25(0.01") unless otherwise noted. 3. lead spacing is measured where the leads emerge from the package. 4. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice .
spec no: dsaj8791 rev no: v.5b date: jan/20/2015 page: 2 of 6 approved: wynec checked: allen liu drawn: q.m.chen erp: 1101026815 selection guide absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1. 1/10 duty cycle, 0.1ms pulse width. 2. 2mm below package base. 3. 5mm below package base. part no. dice lens type v iewing angle [1] min. typ. 2 1/2 wp9294zgc/g green (ingan) water clear 1900 2600 60 iv (mcd) [2] @ 20ma symbol parameter device typ. max. units test conditions peak peak wavelength green 520 nm i f =20ma d [1] dominant wavelength green 525 nm i f =20ma ? 1/2 spectral line half-width green 35 nm i f =20ma c capacitance green 100 pf v f =0v;f=1mhz v f [2] forward voltage green 3.2 4 v i f =20ma i r reverse current green 50 ua v r = 5v parameter green units power dissipation 120 mw dc forward current 30 ma peak forward current [1] 100 ma reverse voltage 5 v operating/storage temperature -40c to +85c lead solder temperature [2] 260c for 3 seconds lead solder temperature [3] 260c for 5 seconds notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity/ luminous flux: +/-15%. 3. luminous intensity value is traceable to the cie127-2007 compliant national standards. notes: 1.wavelength: +/-1nm. 2.forward voltage: +/-0.1v. 3.wavelength value is traceable to the cie127-2007 compliant national standards. 4.excess driving current and/or operating temperature higher t han recommended conditions may result in severe light degradation or premature failure.
spec no: dsaj8791 rev no: v.5b date: jan/20/2015 page: 3 of 6 approved: wynec checked: allen liu drawn: q.m.chen erp: 1101026815 green wp9294zgc/g
spec no: dsaj8791 rev no: v.5b date: jan/20/2015 page: 4 of 6 approved: wynec checked: allen liu drawn: q.m.chen erp: 1101026815 packing & label specifications wp9294zgc/g terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the datas heet. if customer usage exceeds the specified limits, kingbright will not be resp onsible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
spec no: dsaj8791 rev no: v.5b date: jan/20/2015 page: 5 of 6 approved: wynec checked: allen liu drawn: q.m.chen erp: 1101026815
spec no: dsaj8791 rev no: v.5b date: jan/20/2015 page: 6 of 6 approved: wynec checked: allen liu drawn: q.m.chen erp: 1101026815
|
